The Model SSL
deaerator is
fully customizable
and can be ordered
as a tank only or
complete skid
mounted assembly.
The Lockwood Model SSL deaerator is a low profile spray scrubber deaerator. The vessel includes a deaerating section that is integral to the horizontal storage section.
Lockwood Model SSL deaerators are designed to reduce the dissolved oxygen content of the feedwater to no more than 0.005 cc/liter (7 ppb) and reduce the titratable free carbon dioxide to zero. To do this, the feedwater goes through a two-stage mechanical deaeration process.
The incoming water is injected into a steam atmosphere in the top of the deaerator via stainless steel spray nozzles. The nozzles create a hollow conical spray pattern which results in a large surface area allowing rapid heating of the water.
As the water approaches saturation temperature, the dissolved gases are released by the water and carried away by the steam.
A majority of the corrosive gases are removed before the water strikes any steel surfaces within the deaerator. The non-condensable gases are then vented from the deaerator through a stainless steel vent pipe located near the top of the vessel. A valve and orifice are used to control the vent rate.
The hot deaerated water then passes through steam scrubber section of the deaerator. High velocity steam is forced through the water causing vigorous scrubbing of the remaining dissolved gasses.
MODEL 10SSL 15SSL 20SSL 30SSL 40SSL 50SSL 60SSL
CAPACITY (LBS/HR) 10000 15000 20000 30000 40000 50000 60000
STORAGE (GAL) 200 300 400 600 800 1000 1200
STORAGE TANK DIAMETER (IN) 36 42 48 48 54 60 66
STORAGE TANK LENGTH (IN) 72 72 72 120 120 120 120
DIMENSION A (IN) 88 90 92 140 142 144 146
DIMENSION B (IN) 77 77 77 125 125 125 125
DIMENSION C (IN) 64 69 75 76 79 85 91
DIMENSION D (IN) 59 62 68 70 72 78 74
DIMENSION E (IN) 56 62 68 69 74 84 90
STEAM INLET (IN) 3 4 6 6 8 8 8
MAKEUP SUPPLY LINE (IN) 1-1/4 1-1/4 1-1/2 2 2-1/2 2-1/2 3
DRAIN (IN) 2 2 2 2 3 3 3
OVERFLOW (IN) 1 2 2 2 2 3 3
VENT LINE (IN) 3/4 3/4 3/4 1 1 1-1/4 1-1/4
VENT ORIFICE (IN) 3/16 3/16 1/4 1/4 5/16 3/8 3/8
VACUUM BREAKER (IN) 1 1 1-1/2 1-1/2 1-1/2 2 2
SENTINEL VALVE (IN) 1.5×2 1.5×2 1.5×2 1.5×2 1.5×2 1.5×2 1.5×2
CHEMICAL INJECTION (IN) (2) 1 (2) 1 (2) 1 (2) 1 (2) 1 (2) 1 (2) 1
SHIPPING WEIGHT (LBS) 2950 3250 3900 4800 5500 6200 6900
OPERATING WEIGHT (LBS) 4000 4800 5950 7850 9550 11250 13000
FLOODED WEIGHT (LBS) 4700 5900 7400 10050 12500 15000 17400
Larger models up to
1,000,000 lbs/hr are available.
Contact Lockwood Sales for
more information.
NOTES:
- Typical trim and options shown on the Deaerator Option Flyer
- All dimensions and volumes are approximate and subject to change without notice
- Storage capacity based on 10 minutes of storage. Other capacities available upon request.
- Pump connection quantity and size vary by application
- Stand heights vary by application and pump selection
- Steam control valve, and safety relief valve(s) vary by application
- Weights apply to tank and stand only and do not include pumps or suction/discharge piping
![](http://lockwoodproducts.com/dev/wp-content/uploads/2021/03/PICTURE_DA_SSL_DIMENSIONS-1024x578.png)