Customizable Product
CALL FOR DETAILS
RECEIVERS
- Cast iron, rectangular receivers are available with 15 to 110 gallon capacities.
- Heavy duty, welded, rust resistant, copper bearing steel receivers are available in rectangular or cylindrical configurations with capacities ranging from 21 to 1,000 gallons.
Consult your local representative for custom engineered receivers and rust resistant linings.
Lockwood VCS pumping systems are available in simplex, duplex, triplex or quadruplex configurations from 1,000 to 100,000 sq. ft. EDR capacities. Discharge pressures from 10-40 psi are available on units equipped with 1750 RPM motors; 15-75 psi on 3500 RPM units. Standard selections use 1750 RPM motors only on 10 psi applications.
VJ PUMPS
- 1/2 thru 2 HP
- 3500 RPM (Discharge pressures are 15, 20, 30, 40 or 50 psi)
MOTOR TYPES AVAILABLE:
- Open drip proof (ODP) only
- Single phase, 115/230 V, 60 Hz
- Three phase, 208 or 230/460 V, 60 Hz.
VC PUMPS
- 1/3 thru 15 HP
- 1725 RPM (Discharge pressure are 10, 15, or 20 psi)
- 3500 RPM (Discharge pressures are 30 to 75 psi)
MOTOR TYPES AVAILABLE:
- Open drip proof (ODP)
- Totally enclosed fan cooled (TEFC)
- Explosion proof
- Single phase, 115/230 V, 60 Hz
- Three phase, 208 or 230/460 V, 60 Hz
VE PUMPS*
- 3/4 thru 2 HP
- 1750 RPM (Discharge pressure are 20, 25 or 30 psi)
MOTOR TYPES AVAILABLE:
- Open drip proof (ODP)
- Totally enclosed fan cooled (TEFC)
- Explosion proof
- Single phase, 115/230 V, 60 Hz
- Three phase, 200 V, 60 Hz
- Three phase, 230/460 V, 60 Hz
VA PUMPS*
- 3, 5 or 7 1/2 HP
- 1750 RPM (Discharge pressure are 30 or 40 psi)
MOTOR TYPES AVAILABLE:
- Open drip proof (ODP)
- Totally enclosed fan cooled (TEFC)
- Explosion proof
- Three phase, 200 V, 60 Hz
- Three phase, 230/460 V, 60 Hz
CENTRIFUGAL PUMPS
Four centrifugal models are available in a large selection of sizes to meet your specific application requirements: VC, VJ, VE and VA.
The pumps are bolted directly to the receiver to provide a compact, efficient design. Their close-coupled, centrifugal design with bronze enclosed type impeller assures smooth, efficient water passage. A mechanical seal, rated to a maximum temperature of 220°F, is vented to the receiver to assure adequate lubrication at all times.
All standard selections are rated for condensate temperatures up to 200°F. Consult factory for higher temperature applications, as some pumps are available that have low NPSH capability. These pumps have advanced impeller and volute design that can provide true 2ˈ NPSH capacity without using additional impellers and parts required by other manufacturers.
Designed for long-life, low maintenance and reliable service, the pumps are easily serviceable if necessary. Parts subject to normal wear are readily accessible. Impeller and seal can be serviced without distributing piping or electrical connections.
All pumps are close-coupled to heavy duty, ball bearing electric motors. Fractional horsepower single phase motors have built-in thermal overload protection.
To help you determine the appropriate pump type for your application, specifications for each of the four types are described in the next paragraphs. Refer to selection table for additional pumping system performance data.
TYPICAL PUMP CROSS-SECTION
SELECTION DATA
All selections listed below at 10 psi are 1750 RPM – all others, 3500 RPM except 801 1/2 and 1001 1/2
MAX SQ. FT.
EDRRECEIVER
SIZEPUMP CAP.
GPMDISCHARGE
PRESSURE
AT PUMPPUMP
TYPEPUMP
SIZEMOTOR
HPRETURN
PIPE
SIZEDISCHARGE
PIPE SIZE
10 VCS -11 ⅓
15 -11 ½ ½
20 -12 ½ 2″
15 30 -13 ½ CAST IRON
1,000 or 1 ½ 40 VJS -14 1 1 ¼”
21 50 -15 1 ½ 2 ½”
60 -16 2 STEEL
75 -17 ½ 3
10 VCS -21 ⅓
15 -21 ½ ½ 2″
15 20 -22 ½ CAST IRON 1 ¼”
2,000 or 3 30 VJS -23 ½
21 40 -24 1 2 ½”
50 -25 1 ½ STEEL 1 ½”
60 VCS -26 2 1 ¼”
75 -27 ½ 3
10 VCS -41 ⅓
15 -41 ½ ½ 2″
15 20 -42 ½ CAST IRON 1 ¼”
4,000 or 6 30 VJS -43 ½
21 40 -44 1 2 ½”
50 -45 1 ½ STEEL 1 ½”
60 VCS -46 2 1 ¼”
75 -47 ½ 3
10 VCS -61 ⅓
15 -61 ½ ½ 2″
15 20 -62 ½ CAST IRON 1 ¼”
6,000 or 9 30 VJS -63 ½
21 40 -64 1 2 ½”
50 -65 2 STEEL 1 ½”
60 VCS -66 2 1 ¼”
75 -67 ½ 3
10 VCS -81 ⅓
15 -81 ½ ½ 2″
15 20 -82 ½ CAST IRON 1 ¼”
8,000 or 12 30 VJS -83 ½
21 40 -84 1 2 ½”
50 -85 2 STEEL 1 ½”
60 VCS -86 2 1 ¼”
75 -87 ½ 3
10 VCS -101 ⅓ 1 ½”
15 -101 ½ ½ 2″
15 20 -102 ½ CAST IRON 1 ¼”
10,000 or 15 30 VJS -103 ¾
21 40 -104 1 2 ½”
50 -105 2 STEEL 1 ½”
60 VCS -106 2 1 ¼”
75 -107 ½ 3
10 VCS -151 ⅓ 1 ½”
15 -151 ½ ½ 2″
20 -152 ½ CAST IRON 1 ¼”
15,000 21 22 ½ 30 VJS -153 ¾
40 -154 1 2 ½”
50 -155 2 STEEL 1 ½”
60 VCS -156 3 1 ¼”
75 -157 ½ 3
10 VCS -201 ⅓ 1 ½”
15 -201 ½ ½ 2 ½”
20 -202 ¾ CAST IRON 1 ¼”
20,000 45 30 30 VJS -203 1
40 -204 1 ½ 3″ 1 ½”
50 -205 2 STEEL
60 VCS -206 3 1 ¼”
75 -207 ½ 5
10 VCS -251 ½ 1 ½”
15 -251 ½ ½ 2 ½”
20 -252 ¾ CAST IRON 1 ¼”
25,000 45 37 ½ 30 VJS -253 1
40 -254 1 ½ 3″
50 -255 3 STEEL 1 ½”
60 VCS -256 3 1 ¼”
75 -257 ½ 5 1 ½”
10 VCS -301 ½
15 -301 ½ 1 2 ½”
20 -302 1 CAST IRON 1 ½”
30,000 45 45 30 VJS -303 1 ½
40 -304 2 3″
50 -305 3 STEEL
60 VCS -306 3 1 ½”
75 -307 ½ 7 ½
10 VCS -401 ¾
15 -401 ½ 1 ½ 3″
20 VJS -402 1 ½ CAST IRON 1 ½”
40,000 65 60 30 -403 1 ½
40 -404 3 3″
50 VCS -405 5 STEEL
60 -406 5
75 -407 ½ 7 ½
10 VCS -501 1 2″
15 -501 ½ 1 ½ 3″
20 VJS -502 1 ½ CAST IRON 1 ½”
50,000 65 75 30 -503 2
40 -504 3 3″
50 VCS -505 5 STEEL
60 -506 5
75 -507 ½ 7 ½
10 VCS -651 1 ½ 2″
15 -651 ½ 2 4″ 1 ½”
20 VJS -652 2 CAST IRON
65,000 110 97 ½ 30 -653 3
40 VCS -654 5 4″ 2″
50 -655 5 STEEL
60 -656 7 ½
10 -801 1 ½
15 -801 ½ 2 5″
20 -802 3 CAST IRON
80,000 110 120 30 VCS -803 5 2″
40 -804 5 5″
50 -805 7 ½ STEEL
60 -806 7 ½
10 -1001 1 ½
15 -1001 ½ 2 5″
20 -1002 5 CAST IRON
100,000 110 150 30 VCS -1003 5 2″
40 -1004 7 ½ 5″
50 -1005 7 ½ STEEL
60 -1006 10
···································································· Condensate Receivers ····································································
dimensional DATA
VC, VJ AND VE PUMPS WITH CAST IRON OR STEEL RECTANGULAR RECEIVERS